Do you need an air gap with PIR insulation?

Do you need an air gap with PIR insulation?

Insulation is technically a solid with a lot of air in it therefore, it is NOT an air gap. You literally must have a VOID, nothing in the air gap except air itself. So if you are installing under a roof or in a wall, you must create an air gap.

How thick should PIR insulation be?

Three types of PIR Insulation Boards available in different thicknesses, 12mm-45mm, 50mm-100mm and 110-150mm, all especially designed to eliminate thermal bridges, very easy to cut and shape and energy-efficient.

How do I keep Celotex in place?

It won’t get loose mate, if you have any concerns another solution is to buy an expanding foam gun(one you turn the nozzle to control the flow), and spray foam up the edges of the rafters, sealing any air gaps and effectively gluing the insulation in place. Also spray all corners and points of intersection.

How do you screw Celotex?

Use two or three screws per board, then screw the plasterboards through both layers, you are only holding the celotec there until you fix it permanently with the plasterboard, the direction of the celotex wont matter just run them end to end, then mark the rafters for the plasterboard.

How do you fix Celotex between joists?

How to fit Celotex between rafters in 5 steps

  1. Prepare the roof. Before you start fitting your roof with Celotex, you need to make sure the space is clean and clear first.
  2. Take all the measurements.
  3. Create an air gap.
  4. Cut Celotex boards to size.
  5. Install stop battens.

Is PIR the same as XPS?

Polyisocyanurate (PIR) and extruded polystyrene (XPS) are both lightweight, rigid foam boards used for thermal insulation in buildings. It might be assumed that the two materials share a number of similarities, but both have their own characteristics that mean they are actually very different.

How do you fasten insulation boards?

To attach the insulation, you can use screws with large washers, a special adhesive made for adhering foam board insulation or, for smaller pieces, you can seal them in with caulk or spray foam.

Can you screw through Celotex?

What is PIR insulation made of?

PIR is a thermoset polymeric material that combines isocyanates and polyols. The manufacturing process creates a cross-linking chemical reaction that results in a robust, rigid material that does not melt when heated.

Is insulation in short supply?

Insulation shortages are not new In fact, between 2014 and 2016, demand for polyurethane grew around 4.4% per year. From 2016 and 2018 is continuing at that level or higher. Over this time, the production of polyurethane has increased by as much as 4.4% to compensate.

What type of insulation is PIR?

PIR insulation Polyisocyanurate (PIR) is a thermoset plastic produced as a foam. This is bonded to a facing to create an insulation board.

Do I need to replace the insulation on my Pir board?

The need to replace the insulation is highly unlikely due to its rigidity, durability and excellent compressive strength. PIR insulation boards require approximately half the thickness of traditional forms of insulation to meet the same level of thermal performance.

How to fix insulation slabs and insulation rolls?

Another alternative for fixing insulation slabs and insulation rolls is to use insulation hangers, which support insulation within sheeting and cladding systems. Insulation hangers are available as self-adhesive hangers or more basic hangers.

What is the best way to secure insulation?

When fixing insulation boards, helical fixings are a good method of securing them into place. Helical fixings rotate as they are driven in with a hammer, meaning they corkscrew through the insulation and into timber battens or studwork behind the insulation.

What is the best way to fix insulation boards?

Fixings for insulation boards When fixing insulation boards, helical fixings are a good method of securing them into place. Helical fixings rotate as they are driven in with a hammer, meaning they corkscrew through the insulation and into timber battens or stud work behind the insulation.