## What percentage is a 6 in GCSE?

78 – 88 per cent
According to this illustration, grade 4 requires 56 – 66 per cent, grade 5 requires 67 – 77 per cent and grade 6 requires 78 – 88 per cent. ranges may seem extraordinarily narrow and demanding, but they are supported by other evidence discussed below.

## What percentage is a 9 in GCSE?

Setting grade standards for GCSEs A formula is used which means that around 20% of all grades at 7 or above will be a grade 9.

What are the grade boundaries for GCSE 2022?

• 9 = High A*
• 8 = Low A* or high A grade.
• 7 = Low A grade.
• 6 = High B grade.
• 5 = Low B or high C grade.
• 4 = Low C grade.
• 3 = D or high E grade.
• 2 = Low E or high F grade.

How many people get an A in A-Level chemistry?

The proportion reaching the top grades has decreased, with 7.2 per cent getting an A*, down from 8.1 per cent last year, and 28.4 per cent getting an A or A*, down from 30.4 per cent in 2018. This year, 95.9 per cent passed the course, down from 96.5 per cent last year.

### Are 2022 grade boundaries going to be lower?

It means that overall, 2022 results are likely to be higher than in 2019, when summer grades were last determined by exams, but lower than we saw in 2021. As in any other year, grade boundaries will be set at a national level, but only after students have taken their exams, and only after their papers have been marked.

### What is 79% as a GCSE grade?

If a paper is allocated 120 uniform marks, the range of marks allocated to grade B is 84 to 95 (70% to 79% of 120); for grade C, 72 to 83 (60% to 69% of 120).

How do you get an A * Chemistry A Level?

To achieve an A* in A-Level Chemistry, you need to read the examiners’ report and use the specification. The examiners’ report is the third document attached to every past paper and mark scheme, it goes through each question and highlights common mistakes across the country.

Is AQA A Level Chemistry hard?

AQA is quite known for being more strict on their mark schemes. However, from seeing all the other exam boards, they do tend to have the easiest papers in terms of content and knowledge, other exam boards tend to be a little harder, but more lenient on their mark schemes.

#### How much harder is a level chemistry than GCSE?

Looking at the pass rates: the average A-Level has a pass rate of 95.6%, whereas A-Level Chemistry has a pass rate of 96.1%. Therefore, according to the statistics A-Level Chemistry is about as hard as any other A-Level – this doesn’t mean it isn’t a big step up from GCSE Chemistry!

#### Is 3.5 a pass in GCSE science?

In 2018 Ofqual (aka the leader of exam boards), allowed 3-3 as the pass grade for Combined Science, knowing many missed a 4-3. This year, they’ve said that if you get a grade 3-3 or less, then your grade is unclassified (aka you fail).

Where can I find old grade boundaries data for AQA?

If you need older data, please email [email protected]. Grade boundaries from the most recent exam series are on the grade boundaries page. There were no grade boundaries for summer 2020 as there were no exams. Grade boundaries weren’t published for the summer 2020 series as exams didn’t take place.

Do I need to scale the grade boundaries for GCSE Mathematics?

All GCSE units in January 2013 comprise of one component so no scaling is necessary: the scaled mark grade boundaries are the same as the raw mark grade boundaries. For the non-unitisedMathematics (4365F/H)specification, the subject-level and component-level grade boundaries are presented.

## What are the GCSE mathematics (linear) (4365f/h) grade boundaries?

GCSE Mathematics (Linear) (4365F/H) Subject and Component Grade Boundaries- January 2013 exams Subject Grade Boundaries Maximum Scaled Mark Grade Boundaries Code Title Scaled Mark A* A B C D E F G 4365F MATHEMATICS (F) 175 – – – 121 99 77 56 35 4365H MATHEMATICS (H) 175 138 107 76 45 22 10 – –

## Are the scaled mark component grade boundaries shown in the specification?

For theunitised specificationsscaled mark component grade boundaries are shown. All GCSE units in January 2013 comprise of one component so no scaling is necessary: the scaled mark grade boundaries are the same as the raw mark grade boundaries.