Other

How do you configure IP address in Solaris 11?

How do you configure IP address in Solaris 11?

Configuring the IP address

  1. Step 1 : Set the NCP. We would set the NCP to DefaultFixed profile in order to configure the IP address manually.
  2. Step 2 : Check the link status. The command “dladm show-dev” does not work in Solaris 11.
  3. Step 3 : Create a new interface.
  4. Step 4 : Creating IP address.

How do I create a network interface in Solaris 10?

(Optional) To make the interface configuration persist across reboots, perform the following steps:

  1. Create an /etc/hostname.
  2. Edit the /etc/hostname.
  3. Add entries for the new interfaces into the /etc/inet/hosts file.
  4. Perform a reconfiguration boot.
  5. Verify that the interface you created in the /etc/hostname.

How do I find my host IP address?

In an open command line, type ping followed by the hostname (for example, ping dotcom-monitor.com). and press Enter. The command line will show the IP address of the requested web resource in the response. An alternative way to call Command Prompt is the keyboard shortcut Win + R.

What is Ipmp in Solaris 11?

In production environments, it is important to eliminate any single point of failure. IP network multipathing (IPMP) provides a mechanism for building redundant network interfaces to guard against failures with network interfaces, cables, switches, or other networking hardware.

How do I find the Gateway in Solaris 10?

Check the file /etc/hostname. bge0 , the configured IP address could be in there. By default the hostname is listed in that file and the name is looked up in /etc/inet/hosts . From the found entry, the IP address is used together with the corresponding netmask from /etc/inet/netmasks .

How do I check my Internet speed in Solaris 11?

If you have Solaris 11 local repository , you can install iperf using pkg install command on both the hosts in which you would like to measure the bandwidth. The tool name called “netpref” and you can download it from this ftp site.

How do I find IP address on Linux?

The following commands will get you the private IP address of your interfaces:

  1. ifconfig -a.
  2. ip addr (ip a)
  3. hostname -I | awk ‘{print $1}’
  4. ip route get 1.2.
  5. (Fedora) Wifi-Settings→ click the setting icon next to the Wifi name that you are connected to → Ipv4 and Ipv6 both can be seen.
  6. nmcli -p device show.

How does Solaris Ipmp work?

IPMP maintains network availability by attempting to preserve the original number of active and standby interfaces when the group was created. IPMP failure detection can be link-based or probe-based or both to determine the availability of a specific underlying IP interface in the group.

How do I enable Ipmp?

How to Manually Configure an Active-Standby IPMP Group

  1. Become an administrator.
  2. Create an IPMP interface.
  3. Add underlying IP interfaces to the group.
  4. Add data addresses to the IPMP interface.
  5. Add test addresses on the underlying interfaces.
  6. Configure one of the underlying interfaces as a standby interface.

How do I change my IP address in Solaris?

To change an IP address on a Solaris system immediately, use the `ifconfig` command. If the user does not know his/her network interface names, he/she should use the `ifconfig -a` command to list all of the available network interfaces.

How do I find network interfaces in Solaris 11?

Another easy way to quickly check the interface link status – is to check “ifconfig -a” command output. The RUNNING flag is cleared when the link is down. # ifconfig -a …… e1000g0: flags=1000843[UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 192.168.

What is the use of ifconfig?

It is used at boot time to set up interfaces as necessary. After that, it is usually only needed when debugging or when system tuning is needed. If no arguments are given, ifconfig displays the status of the currently active interfaces.

How to configure additional network interfaces using the ifconfig utility?

The ifconfig utility allows you to configure additional network interfaces using the alias feature. To add the alias network interface of eth0, use the following command. Please note that the alias network address is in the same subnet mask.

What does ifconfig eth0 down do?

The “ down ” or “ ifdown ” flag with interface name ( eth0) deactivates the specified network interface. For example, “ ifconfig eth0 down ” or “ ifdown eth0 ” command deactivates the eth0 interface, if it is in active state.

What does the “up” or “ifup’ flag with interface name (eth0) do?

The “up” or “ifup” flag with interface name (eth0) activates an network interface, if it is not in active state and allowing to send and receive information.